How To Install A Gas Range Line
This mail may contain chapter links. If yous purchase through these links, we may earn a pocket-sized commission at no additional price to yourself.
Are you considering installing a natural gas range in your dwelling house?
I did it myself and I have some great practical advice for installing a natural gas stove in your home. I also had to add onto the existing natural gas supply line in my home to brand this work.
It's been quite an ambitious learning experience for me but it'southward also been a rewarding one, besides.
Why? Considering it was easier than I idea and I saved a wad of cash.
Nosotros switched out our onetime electric ringlet range with a natural gas stove. If y'all're thinking almost doing the same or possibly want to extend your existing natural gas lines to a new outdoor grill, for case, I invite you to go comfortable and listen my advice.
The same principles will apply in dealing with bandage iron pipe. Put your mutual sense on overdrive and read on.
Part 1 – The Steps I Used To Install The Gas Range
Disclaimer: I am Not a licensed plumber and this is not a how-to website. I am simply sharing my experience with installing a gas range. Inquire communication from professionals before considering this blazon of project and add together my practical experience for skillful measure out. If you have Any reservations about attempting this type of project, phone call a professional person to handle it for you lot. This is Not a project to be taken lightly. Cheque with your homeowners' insurance carrier for details on this project before attempting.
If you choose to follow the techniques, approaches and methods shown on this site, then you lot follow them at your own take chances. In no way will the publishers of this website be held liable for any injuries or damages, direct or consequential, incurred by whatsoever person who attempts to follow the examples shown herein.
The data in this article assumes that you have natural gas previously available in your home.
#1 – Enquiry brands and comparing shop.
Make sure you do your homework and shop the best brands out at that place.
#2 – Pull out the onetime stove and measure the infinite for the newly chosen gas range.
Most stoves are thirty inches wide. Our former range was a drop-in model so I needed my measurements to be authentic due to switching to a complimentary-standing range.
#3 – Retreat to headquarters (home), mull it over and brand a decision (aka harass my wife into letting me have the stove I craved).
#4 – With measuring tape and digital photographic camera in hand, we went out and made the purchase.
TIP: If the model you are purchasing is on the sales floor I advise yous have measurements and accept photos of the range and where the gas connections are on the stove.
Exist sure to inquire most the gas connector and diameter. Besides inquire what blazon of electrical connectedness you will demand to have available for the stove to operate on.
#v – One of the offset things I did was locate the nipple where I would be connecting the additional pipe and measured the exterior diameter.
Cast fe pipage that is 7/eight″ outer bore equals 1/2″ pipe in the store, meaning that they only get by the within bore. I took measurements from where information technology would connect all the manner to where it would end up behind the stove.
#6 – I read up on the possibility of tapping into the existing gas line in my house.
I saw that if I was careful and followed lawmaking and mutual sense I could save myself a package.
I figured I saved somewhere between $250-$350 dollars based on conversations with a contractor and employees of Home Depot and Lowe's. I spent just under $50 on materials including $xx on a new pipe wrench.
Other supplies included: 2 elbows, 1 t-connect, i long piece of pipe and 3 curt lengths (all cut to my measurements), cap, T2 pipe joint compound and the valve. I had the acquaintance at Home Depot cutting to length all 3 pieces.
He cut them, reamed them and so threaded them, all on one machine. It took about ten-15 minutes due to the constant interruptions from other customers and Depot associates asking this guy questions.
I plain had one of the more experienced employees on site. That made me feel adept nigh the advice I was given and confirmed what I had read on a couple of other websites.
#7 – I close the gas off at the meter.
Once I had all of my supplies on hand and made an declaration to everyone in the house not to strike a friction match, etc., I shut off the gas at the meter on the outside of the house. It but takes a pair of pliers to accomplish this job.
TIP: Exist SURE TO LINE Upwardly THE Hole ON THE Office YOU ARE TURNING WITH THE STATIONARY HOLE ON THE METER. And so PUT A PADLOCK THROUGH IT UNTIL Yous Take COMPLETED THE JOB. You only need to turn it 1/iv of a turn. Information technology'south a ball valve so information technology will turn either mode indefinitely. Just line information technology up and put a lock on it.
#eight – Next, I pre-drilled 1 inch holes for the piping in the flooring backside the stove and through the floor joist for the ninety caste plough I had to make.
I also made a temporary brace betwixt the floor joists for the unattended cease of the xc inch piping to residuum on while I fabricated the connection.
In hindsight I should've waited to drill the pigsty through the joist until I had the piping from the master line connected and was ready for my next move through the joist. Or I couldv'due east taken off about three inches from the 90 inch pipe to accurately align it towards the hole through the floor joist for the pipe.
Why? Because by the time I was at the betoken of putting the piping through the hole in the joist, I had added two 90 degree elbows (one from the existing gas line and one to turn towards the joist), thus adding about an inch+ per elbow due to the threads and the elbow itself.
The effect was that I ended up re-drilling another hole next to the originals. What can I say — We live and learn!
#9 – When I was finally ready to begin, the BIG moment was upon me. I eased the cap off of the nipple to brainstorm
Nothing herky-jerky hither, folks. Nice and slow. In my instance, it was a little tough to start turning the cap due to the onetime articulation chemical compound only it soon gave way. Be sure to open some windows to let the residual gas escape.
It will aroma for a little while but it soon dissipates. Feel gratis to take a short break.
#10 – Articulation compound
was probably the single most important buy. It acts as THE bonding amanuensis between connections and prevents gas leaks from occurring.
I basically just "painted information technology" onto the male person threads thick enough to not be able to see the threads and that's it. No gooping and layering. It's not a cake!
I went from connection to connexion, putting the "pipe dope" only on the male threads. I tightened each connectedness firmly just didn't over practice it then I wouldn't split up or crack a pipage. Hercules need non utilise!
#11 – The concluding slice in the gas pipe installation puzzle was the gas valve.
Just follow the installation directions on the package.
Office 2 – The Gas Leak Test
This function of the chore is EXTREMELY Important. No shortcuts immune here. When everything was completely continued:
#1 – I turned the gas back on at the meter and mixed a concoction of half and half of dishwashing liquid and water in a minor glass per the Habitation Depot guy and what I had read on do-it-yourself websites.
#two – I stirred it around and grabbed a rag.
#3 – I then proceeded to dab the rag in the glass and dabbed it onto each and every connection looking for bubbles.
#4 – Y'all MUST give a 360 degree look on each connexion. Otherwise, you're rolling the dice with your life and your loved ones.
#5 – If you don't see Whatsoever bubbles forming, y'all're aureate. Requite THE Bubbles Time TO Course. The bubbling may not grade right away so take your time with this step…please!!!
#half dozen – Then wait a day, or 2 for the joint compound to cure and go back and cleanse each joint with articulate water. This will prevent the compound from corroding over time. We received a rebate from our local gas visitor – check to see if there are any available where you lot alive.
Office 3 – Preventing Problems With Combustion Equipment
Utilise a properly sized range hood fan if yous utilise a gas range.
All kitchens should have frazzle ventilation to remove odors and excess moisture associated with cooking. While there are various ventilation strategies for kitchens, a range hood is the almost mutual. When using a gas range, a range hood direct vented to the outside should exist used to capture the combustion products. These range hoods should exist sized correctly. For a typical kitchen range the American Order of Heating, Refrigerating and Ac Engineers (ASHRAE) and the Home Ventilation Found (HVI) recommend 100 cfm. Larger fans may need to have makeup air provided to avoid excessively depressurizing the house, causing backdrafting or other problems.
After installation of combustion and/or ventilation equipment, combustion equipment should be tested to be sure that it functions properly.
It is important that your installer conducts a worst-case depressurization test. This combustion condom exam determines if any not-sealed combustion appliances volition backdraft or spill combustion products into the living infinite. Tell your installer this test should employ an established procedure such as Appendix D of the International Fuel and Gas Code or ASTM E1998 "Guide for Assessing Backdrafting and Spillage from Vented Combustion Appliances".
— the EPA on Indoor Air Quality in Homes/Residences
Resource: Hammerzone and DIY Network
I started as a home-stalker… visiting brand new homes nether structure in the neighborhoods near my firm. That inspired me to write about habitation building and home renovation projects — chronicling homes during different phases of construction from a consumer's point-of-view. Basically, the tips yous'll discover in my manufactures are a collection of checklists for what I think should (and should not) get into building or remodeling a quality home.
Source: https://homebuilding.thefuntimesguide.com/installgasrange/
Posted by: williamsmothas.blogspot.com
0 Response to "How To Install A Gas Range Line"
Post a Comment